How to Replace a Kia Sportage Replacement Key

For many Kia models the key comes with a keyless entry system built-in. The key can be compared to an remote control, and can be changed by a new one purchased from an kia keyless entry dealer or locksmith.

Key fobs can stop working for several reasons, including batteries that are dead worn buttons or buttons, signal interference, water damage and a faulty receiver module. Here are some helpful tips to assist you in getting your Kia key fob that is a replacement for the sportage for good.

How to replace a remote key or a smartkey?

The battery in your Kia's intelligent key will eventually require to be replaced, whether it is a remote key that starts with a push button or a regular key that does not contain transponder. This is particularly relevant if your vehicle displays a message that indicates that the smart key or remote has a low battery.

It's a fairly simple procedure. To replace the battery in the keyfob remove the mechanical key from the slit on the back of the fob. Then, pry the cover off. A small screw will be located inside the key fob to hold the battery in the correct position. Remove the old battery by removing the screw with the help of a small screwdriver. Insert the new battery and then close the gap on the key fob.

Test the key fob by pressing the lock/unlock buttons. You're in good shape in case the doors lock and unlock as expected. You can now utilize the hands-free feature to lock and unlock your Kia whenever your fingers start to get chilly or when you need to run errands around Brandon.

Note: Certain key fobs (transponder chip or smart keys) may require their programming done. This requires a programing machine that is only available to the automotive locksmith near me locksmith or dealer. Other keys (non-transponder metal keys) don't require programming. If you're looking to reprogramme your key, you'll need note the key code number on the key code tag.

How to replace the battery

If your Kia key fob isn't responding when you press the lock or unlock button on the fob, it is a clear indication that the battery needs to be replaced. A battery that is not functioning properly can cause other issues, such as the check engine light turning on or the engine not working properly. It is fairly easy to replace the key fob batteries using just a few simple tools.

Be sure to turn off your vehicle and close all doors prior to beginning. Locate the small plastic piece at the bottom of your key fob and gently jiggle it until the metal key is released. The key can be inserted into the driver door handle to unlock your car.

To replace the key fob's battery, take off the rear cover and use a plier bar tool to loosen the latch holding the black negative battery cable. Take the old battery out, and then align the replacement battery to ensure that its "+" side is facing you, and the "-" negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into position with care to avoid using too much force to avoid bending or damaging the contacts on the metal.

After the new battery has been installed and the key fob is turned on, turn it off and on in the ignition for a few times until the door locks cycle. You can then test your Kia's key fob again to confirm that it's functioning properly.

How to replace a smart keys

Depending on the model of your Kia Sportage, you may have an ordinary key fob or a smart key. The smart key comes with an embedded mechanical key blade however, the standard key fob does not. Both kinds of key fobs contain batteries inside which eventually needs to be replaced. It's an easy task that will take about two minutes.

Be sure to turn off your kia niro replacement key and be on a level and well-lit surface prior to you begin. Be aware that the fob has small pieces that could fall should you not be careful.

The release button for the small size is located on the lower backside. This will be either a circular button or a rectangular slot. After pressing this button, the mechanical key blade will come out and you will be able to open the key fob.

Once you have the key fob open, you can simply remove the old battery and replace it. The new battery should be a CR-2032, and can be purchased online or at a local auto parts store. Once you're done, your key fob should be able to lock or unlock and start your vehicle, even if it isn't running.

How do you replace the mechanical key

The kia picanto smart key keyfob is a wonderful convenience that allows us to lock or unlock our car with just pressing the button. As with all devices that is used, the 2010 kia forte key fob key fob may have issues. There are ways to fix these problems and keep your key fobs running for the duration of.

A dead or weak battery is among the most common issues. The battery could cause the device to stop working or work intermittently. If this happens you should replace the battery with a new one.

If this isn't enough to resolve the problem, try using a standard flathead screwdriver and wedge it into the casing of the fob's plastic. Be careful not to damage any internal components or scratch the plastic. When the battery is open, carefully take off the battery that was removed and replace it with a new one.

Once the new battery is in, shut and open the doors using the mechanical key (every Kia fob has an emergency mechanical key that can fit in the slot). Test the key fob to ensure that it's working properly. Contact a dealer locksmith to fix the issue in the event that the key fob is not working. To avoid lockouts in the future, ensure you have an emergency key that can be able to work with all door and trunk cylinders.

좋아요 0