Peugeot 208 Key Replacement

Peugeot 208 key replacement should be left to professional auto locksmiths with the right equipment and technical know-how. They can make and program new keys much faster than a dealership would and at a lower cost.

If the key fob stopped locking or unlocking your doors, it could be due to a dead coin battery. There are other reasons for the key to be malfunctioning.

Dead Coin Battery

A dead battery can stop your Peugeot 208 from locking and unlocking, and also preventing it from starting the engine. In this instance you'll need use the alternative starting method found in your vehicle's owner's manual.

Another reason why your 208 might not start is because the spark plugs are been damaged. The spark plugs ignite the fuel to start the engine. They have a limited lifespan. They'll eventually fail when they aren't used enough.

There is a simple solution for this problem. Examine the voltage of your battery with a multimeter. If the voltage is below 11,5 volts, it's time to replace it. It is also necessary to clean the contacts of the battery if it has corrosion. This can be done by taking off the rubber covers from the two battery terminals, and then using a wirebrush to clean any corroded parts of the battery. Then, reconnect your cables to connect the positive and negative poles.

Water Damage

If your 208 doesn't start and the battery hasn't gone flat, you should inspect the spark plugs. It could be that they're overly dirty, causing them not to spark. This can be easily corrected by cleaning the spark plugs in a workshop.

Peugeot cars use a key with a transponder compatible with the immobiliser. This makes sure that only the correct key is able to turn the engine. If the chip inside the Peugeot key is damaged, then it will not transmit the proper signal to the vehicle.

This is a common problem that is caused by water damage. This is a common problem in colder climates where the vehicle has been exposed to rain or snow. If this is the case, seek out a reputable auto locksmith who will have all of the tools and equipment required to reprogram the new key. They also have the latest technological know-how and the equipment required to make a peugeot rcz key 208 smart key. The process shouldn't take more than 15 minutes.

Contacts to the battery are not working properly.

Peugeot replaced the old transponder chips by introducing a new type that uses electronic components mounted on a circuitboard. The new system is excellent when it's new, however the circuit boards wear out over time and cease to function properly.

This could prevent the immobiliser's function from being activated, meaning the vehicle won't start. If this is the case it's recommended to call a peugeot partner Key Fob specialist or locksmith.

Another issue that is common is when the key fob battery starts to die, this causes the blade of the key to stop feeding into the lock. A locksmith from your vehicle can replace the battery and cut a fresh blade for you, this is generally a quick fix.

Faulty Receiver Module

If your Peugeot key fob was not working after dropping it on the floor, or being exposed to a sudden downpour or accidentally washing it or washing it, it could be due a malfunctioning receiver module. The receiver module is responsible for transmitting radio frequency to the onboard computer which controls the central locking system of your Peugeot vehicle.

The key fob itself has rubber seals to prevent water from reaching the chip inside. Water can damage the chip when it is exposed to the water for an extended period of time. Submerging the key fob into ocean water at the beach or throwing it into the water can be particularly damaging due to the high salt content.

The module must be replaced if the Peugeot spare key does not work anymore. This is only completed by an experienced auto locksmith or Peugeot specialist. Peugeot keys are, unlike other vehicles, are secured by an immobilizer device. This requires the proper programming to allow the car to start. This is the reason that you should only trust a Peugeot locksmith to design and program an alternative.

Computers with faulty on-board computers

The on-board computer of your Peugeot is responsible for a variety of functions in your car including power windows and airbags. The on-board computer displays a code if something goes wrong. This code is stored inside the system and will stay there until the issue is solved. Usually, this will mean replacing the computer on board.

One of the most frequent causes of the airbag light turning on is the loose or corroded connections within the airbag sensor. This can be caused by wear and tear, ageing or exposure to moisture and salt. It is important to have this issue addressed as soon as possible, since an airbag that is malfunctioning can be risky in the event of an accident.

If you notice an error message stating that the card is not found on your Peugeot key fob, the battery in the key fob could be weak or dead. This prevents the key fob from sending a signal that disarms the standard immobilizer in your vehicle. Test this by pressing the unlock key on the fob's key and then trying to start your car. If this fails the battery on the key needs to be replaced.

좋아요 0